I started my DIY Christmas Tree project the same way most craft projects start in my house - by pulling
together paints, scrapbook papers, ribbons, and various other supplies from around my house and piling them all in the center of the kitchen table. After staring at the supplies for a while, I decided to start with the paper mache cone-shaped Christmas trees.
DIY Fur Christmas Tree. Let's begin with the Christmas tree that I covered in white fur ribbon, which I purchased at Michael's. Since the base of the tree would remain exposed, I started by giving the tree a coat of white acrylic paint. I unrolled all nine yards of the fur ribbon and cut strips the right length, then used my hot glue gun to begin attaching the fur strips to the tree.
I was concerned about maintaining the narrow, pointed shape of the top of the tree, so I knew I couldn't have six strip of thick fur overlapping at the very top of the tree. Instead I started by affixing three strips of fur that were only about three quarters of the height of the tree. I spaced these strips evenly around the tree, leaving room between each to affix three more full length strips of fur ribbon.
With the final three strips of fur glued to the lower part of the tree, I used a scissors to cut the top of each strip into a point. I then finished gluing these three fur strips to the top of the tree. The tree initially looked odd because of the different layers of the overlapping strips of fur, but as soon as I fluffed up the fur with the fingers, the tree really took shape and looked perfect.
DIY Bead Garland Christmas Tree. Next I decided to wrap one of the Christmas trees in a silver bead garland that I purchased from Michael's (also on the ribbon aisle). I started by painting the tree white, and, to achieve a glossy finish, I combined my white acrylic paint with some Liquitex Gloss Gel that I had in with my painting supplies.
DIY Paper Heart Christmas Tree. I wanted to cover the third Christmas tree in some music note scrapbook paper that I already owned, though I wasn't sure the best way to go about this. I thought about attaching strips of paper around the tree and then fringing the paper, but I was concerned that the music notes wouldn't read if the paper was fringed. Then I thought about cutting rain drop shapes to glue to the tree, but I didn't want to have to cut them all by hand. I pulled out my Cricut cutter and looked through my cartridges only to discover that none of them had a rain drop shape. I did, however, have a cartridge with an elongated heart shape (the George and Basic Shapes cartridge). I realized that hearts would work just as well as rain drops, since they are also narrower at one end. So, I used my Gypsy to layout the hearts in a way that would allow me to cut twenty-four two inch high hearts from each piece 12 x 6 of scrapbook paper. Then I attached the Gypsy to the Cricut and cut hundreds of hearts in a matter of a twenty or thirty minutes.
After cutting all of the music note hearts, I decided that the tree would be more interesting if I mixed in some fancy papers that would add a little sparkle to the tree. I sifted through my scrapbook papers and cut more hearts from silver metallic paper, as well as from paper that had stripes of beige, white, black and silver glitter.
Since I knew that the paper mache base of the tree would most likely show through between the scrapbook paper hearts, I started by painting the tree with two coats of silver metallic acrylic paint. Then, before attaching the hearts to the tree, I curled each around a pencil. Rather than curing them one by one, I found that it worked well to stack up three to four hearts and curl them all at once. Then I would glue those hearts to the tree before curling three or four more.
I started at the bottom of tree, and used a dot of hot glue at the point of each heart and a dot of hot glue in the center of each heart. I worked my way around the tree, one row at a time. On each row, I overlapped the edges of the hearts, and each row also overlapped the row below.
It was a time consuming process to glue nearly 400 hearts to the tree - about five re-runs of Friends to be specific. Once I finally reached the very top of the tree, I used the pencil to curl the final three hearts in around themselves, rather than curling them so that the rounded ends flipped up. This made the final hearts easier to glue in place and maintained the shape of the point of the tree top.
I am so excited about how these tree DIY Christmas trees turned out! Each one is so unique, but I think they look especially great when grouped together.
It's amazing what happens when you stop procrastinating, spread out all your craft supplies, and just get to work!
Next up I am working on the three flat, chip board trees. Update: Come see how my painted, chip board Chirstmas trees turned out!